Full Bathroom Remodel, Part 5: Laying A Heated Tile Floor

AAA Print

Fifth in an eight-part series on bathroom remodeling

In part 4 of this series on DIY bathroom renovation, we discussed building a custom tile shower from the ground up. Now we'll show you how to install a heated tile floor to keep your tootsies warm as you step out of that shower.

Nowadays, if you're reflooring the bathroom, you should consider heating the floor, even if you don't own a luxury home.

An average heated bathroom floor can cost as little as $250 to $300. The Home Depot and Lowe's carry heating systems aimed at DIY bathroom remodeling, but because this is a project that involves some electrical wiring, you might want to contact a bathroom remodeling contractor. The systems are not complicated, however. A mesh mat with a heating wire is embedded in mortar. A thermostat attached to a heat sensor in the floor controls the temperature.

Finding Power

The power source is your greatest concern. Manufacturers recommend a dedicated circuit, which might mean hiring an electrician. Even if you are confident in your wiring abilities, it can be pretty difficult to run new circuits in some houses -- and that is assuming that you have room for another circuit in your service panel.

But often, you can tap into an existing circuit. The heating pads don't draw much power: A 30-square-foot pad -- which would heat a spacious master-bath floor -- draws only3 amps. If you were heating a large room, you would truly need a dedicated circuit, but the small square footage of most bathrooms makes using an existing circuit an option.

Some digital thermostats designed for use with a heated bathroom floor have a ground-fault interrupter built into them. If that is the case, you cannot tap into the bathroom power, which is already on a GFCI circuit, because two GFCIs on the same circuit won't work. If you have a choice between a 15- or 20-amp circuit, go with the 20-amp.

Also, remember that you only need to heat the areas of the floor on which you will walk -- not under the shower and not behind or beside the toilet. Keep in mind, too, that the heat does not travel far horizontally: If you are stepping a few inches away from the pad, the tile will be cold.

The Installation

Assuming you are installing a tile floor -- porcelain or stone -- here are the steps for laying the heating mats.

  1. Backerboard first. As with any tile installation, lay backerboard over the plywood subfloor. Quarter-inch backerboard is all you need. There are numerous options for backerboard; just remember to follow the manufacturer's instructions. Usually it's nailed or screwed over a layer of thinset mortar. The joints are then taped and covered with thinset.
  2. Matted down. Carefully follow the manufacturer's instructions. Usually, the mat can be attached to the backerboard in several different ways -- with staples, double-backed tape or hot-glue gun. Two important notes: Be careful not to staple the actual heating wire or in any way damage it, and pull as much slack and wrinkle out of the mat as possible as you secure it to the floor.
  3. Top coat. The mat is covered with thinset and tile. You have two options: You can coat the mat with mortar, let it set, then lay down the tile with another coat of thinset; or you can put down the tile all in one step -- a thick coat of thinset over the mat and the tile atop it. The latter option is quicker, but can be a little tricky to keep level as you are trying to set the tiles over a deeper soup of thinset.
  4. Wired. Run the power lead and temperature-sensor wires through the wall's base plate and up the wall to the thermostat, where they should meet up with the house current that you have already provided.

Heated floors mean a little more work and expense, but your toasty toes will thank you.

Next, part 6: installing the vanity

Original content written by Jim Mallery, Improvement Center Expert at Improvement Center.

Last Updated: September 2, 2012
AAA Print

Note: The information provided on this site may be provided by third parties. The owners and operators of this site do not guarantee the accuracy, completeness, and compliance of the content on this site. Such content is not and shall not be deemed tax, legal, financial, or other advice, and we encourage you to confirm the accuracy of the content. Use is at your own risk, and use of this site shall be deemed acceptance of the above.